voltage range 50 to 600 volts 8.0 amperes features ? low forward voltage drop ? high current capability ? high reliability ? high surge current capability ? good for switching mode application high temperature soldering : 26 ? 0 o c / 10 seconds at terminals pb free product at available : 99% sn above meet rohs ? environment substance directive request mechanical data ? case: molded plastic ? epoxy: ul 94v-0 rate flame retardant ? lead: lead solderable per mil-std-202, method 208 guranteed ? polarity: as marked ? mounting position: any ? weight: 2.24 grams maximum ratings and electrical characteristics rating 25 ambient temperature uniess otherwies specified. single phase half wave, 60hz, resistive or inductive load. for capacitive load, derate current by 20%. type number SF801 sf802 sf803 sf804 sf805 sf806 sf807 units maximum recurrent peak reverse v oltage 50 100 150 200 300 400 600 v maximum rms voltage 35 70 105 140 210 320 420 v maximum dc blocking voltage 50 100 150 200 300 400 600 v maximum average forward rectif ied current .375"(9.5mm) lead length at tc=100 8.0 a peak for ward surge current , 8.3 ms single half s ine-wave super imposed on rated load (j edec method) 125 a maximum instantaneous forward vol tage at 8.0a 0.95 1.30 1.70 v maxi mum dc reverse cur rent tc=25 at rated dc b locking vol tage tc=100 10 500 a a maximum reverse recovery time (note 1) 35 50 ns typi cal junction capacitance (note 2) 50 pf operating and storage temperature range tj, tstg -55 +150 notes: 1. reverse recovery time test condition: if=0.5a, ir=1.0a, irr=0.25a 2. measured at 1mhz and applied reverse voltage of 4.0v d.c. to-220ac unit:inch(mm) .419(10.66) max .196(5.0) .163(4.16) .054(1.39) .045(1.15) .114(2.9) .098(2.5) .025(0.65) max .139(3.55) .min dia pin1 32 .177(4.5) .max .038(0.96) .019(.5) .100(2.54) .624(15.87) .548(13.93) .50(12.7) max .269(6.85) .226(5.75) data sheet SF801~sf807 semiconductor http://www.yeashin.com 1 rev.02 20110725 c c c c c
ratings and characteristic curves 0.1 0.1 1.0 1.0 .01 10 10 50 100 1000 fig.3-typical forward fig.4-typical reverse fig.1- test circuit diagram and reverse recovery time characteristic characteristics characteristics fig.2-typical forward current average forward current,(a) fig.5-maximum non-repetitive forward surge current fig.6-typical junction capacitance reverse voltage,(v) junction capacitance,(pf) instantaneous forward current,(a) reverse leakage current, ( a) forward voltage,(v) pulse width 300us 1% duty cycle 2 4 6 8 10 12 175 150 125 100 75 50 25 0 (+) (+) 25vdc (approx.) ( ) ( ) 10 noninductive 50 noninductive ? ? pulse generator (note 2) oscilliscope (note 1) 1 non- inductive ? notes: 1. rise time= 7ns max., input impedance= 1 megohm.22pf. 2. rise time= 10ns max., source impedance= 50 ohms. +0.5a 0 -0.25a -1.0a | | | | | | | | 1cm set time base for 50 / 10ns / cm trr .01 .05 .1 .5 1 5 10 50 100 d.u.t. .4 .6 .8 1.0 1.2 1.4 1.6 1.8 3.0 single phase half wave 60hz resistive or inductive load derating curve 600v 100v-200v tc=100 c tc=25 c tj=25 c 25 0 50 75 100 125 number of cycles at 60hz 1 10 5 50 100 tj=25 c 8.3ms single half sine wave jedec method 0 0 25 50 75 100 125 150 175 case temperature,( c) 0 percent of rated peak reverse voltage,(%) 20 40 60 80 100 120 140 peak forward surge current,(a) 300v-400v SF801~sf807 http://www.yeashin.com 2 rev.02 20110725
|
